A world about Project Rosetta Stone

When our first moderator of our Facebook Group, Arthur Hendrix had to step down due to a very demanding schedule we added Steve Lydon in his place and then also Leslie Yagin. Leslie wanted to help out new pilots. We had noticed that some people were sitting on the fence with building their first INAV plane. It was a bit overwhelming. That was what inspired us to create Project Rosetta Stone.

The original idea was that we would build a plane such as the Reptile S800 as a group. But, some people wanted to follow along with other planes than the S800. And worse yet, INAV 3.0 was just starting to get hinted about right after we announced the project. We gave people time to order their parts for the S800 build.

A number of people are waiting on INAV 3.0. Which is fine, because the steps for the build up to this point only change in the respect to the firmware. It’s the tuning process that will be different. However, if you follow along with this guide we broke down a fairly complex subject into smaller parts that are easier to manage.

Where you should be right now

One of the harder aspects of building a plane is understanding the parts and what different ones will do for you. Along the way we’ve suggested some very good parts. Leslie actually took the parts that we suggested (all of them) and built the plane on his own. He never built the S800 and really likes it. So, yes, the parts are very solid.

You had to solder the flight controller and that wasn’t easy. Then you had to build the plane, then fit in the electronics. This isn’t a simple plane to assemble. Sure, you could assemble a bind and fly plane in under and hour and be off to more fun. The point is that struggling during the build will teach you things along the way. There is also a sense of pride and ownership when you see the plane flying. 

Right now, your plane should be nearly assembled. You should be tying up loose ends because next week the plane gets off the ground for it’s first flight. Your wiring should be either glued down with something like E600 or taped down the 3M Blenderm.

By now, your plane should arm, the motor should spin in the right direction and your servos move the control surfaces in the right direction. Here are some important steps you should do at this point.

Backup your Diff/All and Dump files.

You need to have Diff/all and Dump files from your CLI saved to your computer.

Start Documenting your plane

We created a master build sheet document for you to copy and follow along. You may not be the type that documents things as they go along. It’s a good idea to get into the habit. One of the main benefits is that a plane build, especially when you start building your own is a huge mental exercise. You will contemplate the motors and servos. Then, five weeks later when stuff starts showing up from China, you can’t remember what plane the new shiny motor goes to.

More importantly, when you have problems along the way, when you ask for help, we will have a very good idea of what you’re doing with your plane. You will get much better help.

Instead of copying and pasting the contents of the document into a message on Facebook, use an online service like Google Docs so that you can just provide a link to the document. This is also helpful as you change things it will let everybody who is following along know what is happening.

Double down on the CG

Center of Gravity is really one of the things that will make or break your flying experience. And yet it’s one thing many new pilots blow right past. If you’ve come to us from quads, this may be all new to you. I wrote this for a document a couple of years ago. It’s about as simple of an explanation about CG as you will find.

Center of Gravity (CG)

In the group, so many of the maiden flight issue’s we hear about come back to CG issues. If you can’t get the CG right, not only will it affect manual, but also the other flight modes. When we see people showing pictures of crashed planes, very often it comes back to CG.

“A casual relationship with CG leads to an intimate relationship with your glue gun.“

To illustrate CG in a simple form, look at this. The seesaw is a fixture on children’s playgrounds. Kids understand that if they have a friend who is around the same height and weight they can take turns going up and down. In this example the center of gravity is the middle of the seesaw. What they are doing is going up and down on the pitch axis.

When one of the boys leaves and dad takes his place, dad weighs 3 times as much as the son. When dad sits down the young boy has no way to lift him. In order to balance dad would have to move closer to the center of gravity, much closer.

Weight Placement

What is so obvious with this example is somehow lost when it comes to weight placement on planes. If you want to get by with making your plane lighter put more dense weight at the extremes of the counterbalance. Seek out taller, fatter battery packs instead of the longer skinny ones. And yet, if you can get by with a lighter motor, perhaps 10g lighter, depending where the motor is located on the plane you may save another on the counterbalance making the total weight saving on the plane 50g. On smaller planes this may make a huge difference.

Sometimes you’re stuck where the battery is placed. Often what is done is to place small lead weights further to the extreme of the counterbalance. If you’re putting it on a delta wing for example, the weight would go on the nose. The idea is to help keep the total weight of the plane down by using small amount of weight on the nose than much larger amounts of weight closer to the CG.

The major point is; the difference between a plane that flies great and one that you just tolerate usually comes down to CG and weight. We can talk about putting your plane on a diet and we can talk about CG. The only other things you can control is surface deflection and the placement of gear on the airfoil.

Marking CG

This is a great idea and the reason why it’s a great idea is because I didn’t think of it! To execute on this idea you’ll need to go to order map pins from Amazon. I don’t have a reseller account and I am not the biggest fan of Amazon, so if you can find them elsewhere, be my guest. What I like about them is that the colors are segmented. They have fat heads which is important and they are short. Use them to mark CG.

The center of gravity isn’t parallel with the leading edge of a wing. Look at this image.

That BMW symbol looking thing is the CG mark for the plane. The blue line that comes from it is the axis of the CG. If you were to cut on the line you would have 1/3rd of the plane in one piece and 2/3rds in the other piece. And that’s the most standard explanation of CG. It’s ⅓’rd of the wing. Draw this line. If you don’t want to mess up the beauty of your plane make small marks near the leading edge. This is important. Don’t do a so-so job. Measure the length from the nose to the mark. They should be exactly the same length. Stick pins on those marks. You can feel them with your fingers as you balance the plane.

You will need to be able to hold the plane up, even for a brief moment on the pins. You’ll need to put the battery in. If it falls backwards you’re tail heavy. Put more weight in the nose or figure out how to move more weight from the back of the plane (RX, VTX, your flight controller should be on the CG) closer to the CG. If the plane falls forward move the battery back closer to the CG if you can. If you can’t you will either need a lighter battery, or you will need to figure out how to place more weight near the back of the plane.

Adding reflex

This has been a topic of quite a few conversations in the group. Level flight most often means you’ll be losing altitude. It has to do with the design of the plane and inherent inefficiencies. Thus, if your elevons or elevator are perfectly level (not up or down) on the plane you would need to hold some back stick to keep the plane from meeting the ground. Deflection, or reflex, means that we’re permanently doing this by moving the elevators or elevons up a few degrees. How much depends on the plane, but start out with a mild few degrees and keep them level.

What are Elevons?

Elevons on flying wings and tailless planes, comes from the combination of words Elevator and Aileron. When one elevon goes up and the other goes down. This is acting as an aileron. It turns in the direction of the one going up . When both go up or down at the same time they act like elevators. As this is a mix of two surfaces. In the mixer you will see 50% weight, not the 100% that you would have on a standard aileron or elevator.

The problem with elevons is that if one goes up or down more than the other the plane will gain or lose altitude, and also gradually turn in the direction in the elevon that is higher than the other. And yet, when you trim your plane don’t be surprised that one elevon is up higher than the other to gain level flight. This may be caused by more weight on one wing or something on the wing (A camera, VTX, antenna) causing drag. You can create a counter balance on the other wing to help fix weight issues. You may also consider burying things like receivers and GPS units in your wing.

We also have a document on making a CG bar. You use this to help you find CG on our planes using standard pencils. I waited years to make this thing and regretted waiting so long.

LED Lights

For extra Credit, put some LED lights on your build. Darren Lines has a brilliant video how to set it up in INAV.

Auto Launch?

If you want to setup Autolaunch correctly, follow the guide Setup Nav Launch from our website.