S800 Maiden Week

By now with the S800 you you’ve build your plane as best as possible. If you have never built and flown a plane before you’re at a disadvantage. If you’re on your own trying to figure this out, it’s even harder. Pick a nice soft area to take off from, preferably grass because there may be quite a few failed launches. If you have a friend who knows how to build and fly planes, this is the point you should hit them up for help. At this point, everything will be manual and they should feel quite comfortable with that. If you want to double check your INAV setup has all the basics, you can use this checklist.

How to launch a plane

Here’s a pretty good tutorial about hand launching. If this is your first experience with planes, get someone to launch it for you. They can follow the tutorial, or find more videos about hand launching.

All the videos I’ve seen don’t show my technique for launching. I do it almost exactly like in the videos. The only real difference is that I use my left hand to launch the plane though I am right handed. The right hand is holding the elevator up with the sticks. It takes some getting used to , but seems to work well for me.

A few good tips

  • Usually planes like flying wings take off fairly close to full throttle. 
  • The plane will need a good push into the sky
  • The heavier the plane, the harder the push you’ll need.
  • Be sure to have a nice fluid throw where you let go of the plane so that it travels straight.
  • This is a technique, you will get better with practice.

Expect a crash

Flying wings are a bit different than planes with tails. They are a bit more chaotic, and a lot more hands on. The first attempts to get airborne may not work out. Again, if you have a friend who knows how to fly, they will help get you in the air much faster. If not, consider taking along someone who can video you launching the plane if this is your first time. If you can share your video with the group we can help figure out how to help you.

Please follow these steps

  1. Check the servos with a High Five Test to ensure that they go the right direction.
  2. You’ll want a relatively calm day without a lot of wind. Empty parks first thing in the morning are often a good suggestion.
  3. Make sure nobody is in your flight path, this plane may come down and you will want to make sure you don’t hit someone by accident.
  4. Make sure your plane is in the manual flight mode.
  5. You will need to find at least 6 satellites before the plane can arm. When the plane is ready to arm, your GPS warning will go away.
  6. Arm your plane and raise the throttle. If the plane is blowing air the wrong direction you will need to reverse the motor by swapping two bullet connectors, or by going into BLHeli and reversing the motor direction.
  7. The very small numbers on the prop need to go in the direction of flight. If the plane sounds like it’s about to moo like a cow, your propeller is backwards.
  8. Hold your plane with a limp wrist. When you fire up your motor to a certain point, usually greater than 60% throttle the plane will feel like it wants to fly out of your hand. It will start to be buoyant by itself. You need at least this much throttle to take off.
  9. Even though the plane will feel like it’s ready to fly out of your hands, if you simply let go it will fall to the ground. You need to give the plane a strong push into the air slightly upward and straight forward.
  10. When you finally do launch it, one of many different possibilities will happen.

So, what happened?

The plane crashes near your feet

If the plane goes straight down that’s usually a bad sign, like your elevators are working in the wrong direction, you have too much nose weight, or not enough thrust. At this point, you need to stop and come back to the group and tell us what happened. If you’re afraid of crashing so you gave it low throttle and not much of a push, this is what happens. Give it a lot more throttle and a hefty throw the next time.

The plane flies a bit and then crashes

To use a golf analogy, if you hit the ball and it flies 100 meters off into the rough, it’s progress. You hit the ball and it’s going mostly the right direction. It would be even better if it landed on the fairway, but at least you hit the ball. A plane that almost flies is far better than a plane that crashes quickly. It could be a bad throw, not enough thrust, or perhaps you need more reflex in your elevons. Give it a couple more tries and if it doesn’t fly, come back to the group and describe the problem. You can also reach out to Leslie Yagin to help you with this situation.

The plane takes off, and does a torque roll into the ground

There are some planes like the SonicModell HD wing that are famous for providing so much toque on take-offs that the plane rolls as it takes to the air if the propeller is too large. Or, this could be a sign that the plane is tail heavy. If you start flying the plane and it’s very uncomfortable, it’s certainly a sign that the plane is far too tail heavy. You’ll need more weight in the nose.

Let’s assume you can get the plane flying.

This is the point where your plane could be great, or full of problems. If it will be your favorite, or a shelf-queen. There is only one time we use radio trims, and it’s at this spot. If you’re holding back the stick so that the plane doesn’t crash into the ground you can use the corresponding elevator trim to do this for you. If a wing is dipping to the left you can give it some right elevon (aileron) trim to fix this.

After a few minutes the plane should be flying around fairly well, with the radio trims set. You simply land it and stick pins in your control surfaces so that they don’t move. Then loosen the control rod, so that if you move the servos, the rods don’t move the control surface. Next, put the radio trims back to zero. Then tighten up the connections to the control surfaces and remove the pins. Take it up for another flight. You are at zero trim, but the control surfaces are where they were with radio trims on the last flight. The plane should fly even better. I find that I often have to fly four or five flights until it’s more or less perfect. 

This manual trim is your INAV foundation. Sometimes you get lucky and the plane is more or less perfect on the first flight. Or sometimes you’ll play with it for a number of flights. When your plane is flying in manual without radio trims and it’s a nice experience, everything else will go right into place.

So, is this really even necessary anymore?

As we mentioned before; as we started to work on this project INAV 3.0 was being developed. It released right at this week 6 as a release candidate. Chances are good that if you’re taking on the project after June of 2021 INAV 3.0 is out and maybe even other versions are out. INAV 3.0 got rid of the Autotrim step altogether. Two things take its place

  1. Continuous Servo Trim Instead of servo autotrim being a one time process the servos autotrim on a per flight basis. This is certainly an improvement.
  2. Auto-board level Though this isn’t part of the trim process the plane can further help your flight along by helping the plane find and maintain level flight.

With all of this in mind, you can craft a fairly reasonable argument that all of this polishing the manual mode isn’t needed anymore. I can support that argument to a certain extent. However, a plane that flies well in manual mode, it will fly great in INAV. With a plane that flies badly in manual, INAV is just trying to polish a turd.

At one point, when I first started to get INAV working, I was duplicating the Diff/All files from one plane and putting it on another. That included the board calibration as well. Here’s what I learned. It worked. I mean, I could usually get a plane flying and it sorta worked okay. It was flying and I was happy enough. If I put the plane into manual just about anything was possible including an instant crash. I evolved my thinking to go right to an autotune. Forgetting for the moment that the plane wasn’t trimmed manually nor did it have an autotrim.

In my defence, we didn’t have a lot of good information in the group until around the end of 2019. So, many of my first experiences trying to figure out INAV were in a vacuum. We had some group members who shared information here and there. Thus, I can realistically plead ignorance, mixed in with some stupidity. What changed was that the information improved, and most importantly, I started to figure out what good INAV flights should look like. Thankfully, I saved my old flight video from my goggles on my hard drive. I can look back with astonished-horror at my earlier flights.

Putting pride in your build

When you buy a PNP plane from Horizon Hobby, it’s a complete concept. Perhaps it’s a beautiful scale plane and all you have to do is add the specified battery and bind it. For a lot of people, this is the winning ticket. All the CG issues are worked out and it more or less will fly well out of the box. 

The build from the ground up world is very different. The Reptile S800 is blank canvas. It can be extraordinary, or absolute garbage. We gave you some clues as to what to use for the parts. Perhaps at first plastic gear servos and Racerstar motors are good enough. But, it doesn’t take long to start to anticipate what better motors can do, and what digital servos can do for the plane. We did emphasize the build process and about keeping weight issues in mind. And not having things interfering with the airflow of the plane. Perhaps you went into fine detail to get the wires tucked in and make it look clean.

This all doesn’t matter if it doesn’t fly to it’s true potential. You should be able to drop into manual mode and fly the plane. Chances are you may flip on the manual mode by mistake and if the first thing it does is go into an uncontrollable dive, no other modes may save you. Getting this plane fly well in manual means that the plane isn’t constantly trying to compensate for poor flying characteristics.

In the end, you’ll start looking at planes that you’ve never flown. You can start working out the parts to use in your head and you can anticipate how it will fly. When you get to this level, you will never be satisfied with a plane that comes out of a box with plastic servos and a cheap powertrain. For a bit more money you can build a plane that is first class that will fly much better than the PNP version. But, in order to really get to that last step you need to make sure that the plane flies to its full potential. That means taking the time to do the best tune you know how.

Change of plans

There was supposed to be two more weeks of Project Rosetta Stone. One for Autotrim, one for Autotune. Now, there is only one more week. Let’s say that you’ve followed the guide and have INAV 2.6.1 on your plane. You can go ahead and do the manual trim. The manual trim in INAV 2.61 will transfer over to INAV 3.0.

We won’t take you through the steps of performing an auto trim when in a few weeks it will be obsolete. However, if you want to stick with 2.6.1, you can follow our tuning masterclass. There isn’t much that has changed up to this point other than you will want to load INAV 3.0 or newer on your flight controller.

We also don’t want to encourage you to put the release candidate on your build and then go back again in a few weeks and put the stable version on it. So, for now we’re going to pause this project. Please do your manual trim and if you feel adventurous enough, try out some of your flight modes. The last section is coming and we’ll explain what things you may want to include with your build that are new to INAV 3.0 and how to do the one step autotune. Please expect the last section in June of 2021.