An unexpected phone call
“Hi, this is Chris. I was just calling. I think I found one of your little flying devices things that you might have made yourself, but I figured I’d call you and see if you wanted it back. We have it and it’s still intact for you. My phone number you can reach me at is XXX. Hope to hear from you soon. Thank you.”
This was Angel, June 7, 2020. I lost her about 10 minutes after taking this photo.
And this was Angel after having been lost for 335 days.
What happened?
It’s hard to remember exactly what happened because this dates back about a year. I remember building this plane because I used a shiny lacquer at first but that didn’t look right so I laminated it. Piecing together what I can see from old flight footage the plane flew fine. But the strange little VTX antenna made the video signal turn to static at 600 meters.
Around a week before losing Angel, I had her out flying around and it crashed on the golf course. A golfer took the plane home and started to pull off the lamination and disassemble the plane. Then he found my phone number and called me. I got the plane back in pieces. So, it was rebuilt, this time I had just put on the SunnySky X2212 V3 1400KV motor before I lost this plane. I remember that it was on the other side of the golf course around the 600 meter range when it went down.
I don’t really know exactly how it crashed, but the same plane had an issue with the INAV bug that was eventually fixed. The plane disarmed about a week prior, but I was able to retrieve my plane. I think the combination of stronger motor and horrible VTX reception caused this plane to lose video signal and it crashed before I could bring it back.
This time it sat near a bridge at the golf course when a local resident spotted it while out walking her dog. She had her boyfriend go down the gully to get it.
The liberators of Angel.
Tolerance of wonk
In my book there are two extremes, wonk builds and anal retentive builds. I’ve had conversations with people who make anal retentive builds. What should be a 20 hour build turns into a 60 hour build. They bury everything and paint the wires the same color as the fuselage. The plane is perfect. So much pride goes into their build that the thought of crashing the plane causes anxiety. It’s a bit unhealthy.
The other extreme is the wonk build. These are builds where perhaps too little pride was used, and too much was overlooked. Though this plane didn’t start off as a wonk build, it certainly ended up as a wonk plane. There were issues that weren’t addressed which hopefully now have been addressed with it’s second rebuild.
I have a much lower tolerance for wonk.
The dirt is thick with this one.
I am not seeing mud as much as I am seeing dirt. In my side yard I have a 10’x10’ area where I place the trash cans. Every week I sweep up a pretty good amount of dust. I think the plane was protected but dust and spiders had their way with Angel. As I started to clean her a very angry spider jumped out of the fuselage and took up residence somewhere in my side yard.
Against everybody’s best judgement I plugged her in and everything fired up, but there was no video other than black to signify it was transmitting.
Where was Angel?
I checked the blackbox and she ended up here.
I thought she ended up in the backyard of the houses next to the golf course. This more or less went along with the story that the people who found her told me. And yes, I kinda knew where it landed. I guess I should have snuck onto the golf course at night and investigated.
Formulating a rebuild plan.
This type of thing happens quite a bit in our group. The further away you fly, the more likely you will lose a plane for a while until you get it back, if you get it back. So, I will document how I rebuild Angel. Obviously, the VTX antenna needs to be improved. The flight footage I could find was fine. So, here are the repair ideas.
#1. Remove all electronics and clean the electronics with alcohol and let dry.-Done
#2. Strip off the decaying lamination-Done
#3. Give Angel a very deep bath-done
#4. Replace the cheap servos with better digital servos-Nope
#5. Put on a better VTX Antenna-Done
#6. Put on a better LED light-Not Yet
#7. Fix a minor break in the foam where the wing meets the fuselage.-Done
#8. Remove the motor and blow it out-Done
#9 Check all wire and solder joint, repair them or replace bad/old/defective wire-Done
10. Place the electronics neater on the outside of the plane-Dpme
11. Clean up the fuselage’s wiring. Make it neat and tidy-Done, though more work is needed.
The stripdown
Removing the electronics wasn’t that bad. The VTX was actually glued onto the lamination. Thus it was as simple as cutting out lamination. The BEC came out with ESC. It looked fairly clean. But all the components will be checked over before reassembly.
Pre-bath
Notice how the left side looks clean but the right side looks dirty? And the dirt goes up to the screw? What I suspect was that the plane was sideways and that from what I can see the water missed the flight controller.
Angel gets a bath.
The servos were well covered with lamination so I didn’t remove them. The plane got a good washdown and looked remarkably cleaner afterwards. It’s now clean enough for me to finish taking off the lamination. The plane was filthy and had a bad smell before the bath. Now, she’s great!
Checking out where it stands now.
The VTX is missing the video wire- Taking a closer look at the wiring, I will gladly replace all the wiring on the VTX. The old wiring is thin and looks to be sun bleached. I did check and the VTX does work. Still I spent a few minutes and clean it a bit more.
This is the side that was facing down on the plane. Still the video wire fell off and the other wires started to change colors. Could I make this work? Perhaps. But instead I peeled away the black plastic over the terminals, turned the heat up a bit on the soldering iron and removed all the old wires. The black plastic needed to be scored with a knife, then it came off in larger pieces fairly easily. Silver solder seemed to melt off at around 400 degrees celsius.
I did this VTX and then I did another 805S VTX that had a broken wire. That solder job turned out to be even better. What I discover was to
- Cut the wires to the desired length
- Tin each wire
- Tin the pads
- Solder on the wires onto the VTX
I did this in around half the time of the first VTX and the solder job looked even better.
I used 26 AWG silicone wire. As you can see it’s much thicker than the wire that came with the VTX. I just may start doing this with all my VTX project, I guess this is a test Though I don’t mind soldering wire onto the wire that comes with the VTX, one less solder joint wouldn’t be a bad thing.
Reworking the Flight controller and PDB
The plane had my trusty Matek F405-STD with the matching 6S FCHUB PDB. This is a combination I trust to the end of the earth and back. The way that the plane was situated when it landed meant that as far as I could tell the flight controller and PDB didn’t get wet. They were full of dust and cobwebs (see above). Contact cleaner and a light brushing took care of all of it. The flight controller worked. So just use it and move on? Nope. It was time to rethink the wiring. I moved the solder S1-S3 pad down to the PDB where they should have been.
Removal of wires from the top
One thing that I will work on as much as possible with INAV Rehab is to clean up the wiring on the planes. Stands of wire and the occasional heat shrink running on top of the plane just is unsightly. I moved the VTX to the bottom of the plane which is both good and bad. It’s hidden behind the FPV camera mount so it doesn’t add drag. But it does raise the risk of it getting wet when landing on wet grass. Only the antenna sticks up from underneath the plane which is much cleaner looking.
The GPS wiring is also run from underneath as well as the RX.
Fixing broken foam
The plane had the lightest of crashes because there wasn’t much damage. But there was enough that it needed some attention. At the joints I reglued the foam. I worked one problem area at a time. There were three areas of concern such as where the wing met the fuselage. I didn’t try to mass glue all the problem areas at once. Just on area at a time. This reinforced the plane and the 5 mil lamination only reinforced the glue. So now, it’s back to normal.
Spray painting the exposed wood
The dirt that got into the pores of the wood wasn’t coming out. I could have perhaps sanded the areas over and over again. I opted to paint them black.
Yaw Waggle
One of the smart things I’ve done is keep my old flight footage. I don’t need to take the plane up for a flight to know what’s wrong with it. This plane has a very real issue with yaw waggle. Before it goes up again, the winglets need to be perpendicular to the wings. Also side to side balance needs to be adjusted. I still believe the plane if very flyable
It works, but can you really trust it?
No, I can’t trust it. Just the same, I don’t trust anything I build. I have to fly it for a while to learn more about the ups and downs of the plane. The larger question is, are the electronics potentially not suitable for flying? They look fine and work fine, so they are under a ‘trust but verify’ status until I have put through around 5 battery packs.
What I’ve learned from this experience.
When the plane crashed I went to the front of the golf course and tried to see if anybody was bringing it out. Nobody did. I kept asking the gardening staff if they had seen it, they hadn’t. Someone did find it, but it took about a month for them to turn it over to me. I think the first few weeks they did like most people do “finder’s keepers, losers weepers.” But the electronics may have been daunting.
The plane is a snapshot of how I approached INAV and flying in general in June of 2020. I have lost track of what I thought was good and what I do these days. I am more about clear airfoils and making sure that problems are handled. I should have brought this plane down at the first sign of trouble and taken the plane home and fixed it. I did mourn the loss of this plane and now I am rejoicing to have it back.
Angel 2.0
Surprisingly, everything but the battery and front cover survived the crash. I was able to reuse everything. I did go back through and fix the solder joints. And, at one point I was having problems getting the FPV camera to display. I switched out the flight controller just to be safe, but it wasn’t the issue. I will use that flight controller for other projects.
The plane looks no worse for the wear and tear.
I do have fresh canopies in my inventory. But hey, this one still works. And besides this will be a local park beater plane

Though the plane has a wrapped in plastic look going for it, it’s sealed against moisture.
Still waiting on the maiden
It’s been very windy all week and Angel has been moved off to the sidelines. She had her Foxeer camera replaced with a cheap Eachine FPV camera because it was around the only thing that worked. It will test out with INAV 3.0 release candidate. Because, what’s a better idea than flying a plane that crashed multiple times with a release candidate?
I may put the cheaper Sunnysky A2212 1400KV on her instead. I can free up this motor for another AR Wing. I also 3D printed some nice LED holders that may go on the back of Angel.
